接線端子是用于實現電氣連接的附件產品，在工業上屬于連接器。隨著工業自動化程度的不斷提高和工業控制的要求越來越嚴格和精密，接線端子的需求量逐漸增加。電子行業的飛速發展，使得接線端子的用途越來越廣泛，越來越多樣化。

Wiring terminal is an accessory product used to realize electrical connection, which belongs to connector in industry. With the continuous improvement of industrial automation and the increasingly strict and precise requirements of industrial control, the demand for wiring terminals is gradually increasing. With the rapid development of the electronic industry, the use of wiring terminals is becoming more and more extensive and diversified.

端子的塑料絕緣材料和導電部件直接關系到端子的質量，它們分別決定了端子的絕緣性能和導電性。任何一個接線端子的故障都會導致整個系統工程的失敗。警告案例不用多說，這里就不一一列舉了。

The plastic insulating materials and conductive parts of the terminal are directly related to the quality of the terminal, which determine the insulation and conductivity of the terminal respectively. The failure of any terminal will lead to the failure of the whole system engineering. Needless to say, there are not many warning cases listed here.

為保證端子的質量和可靠性，防止相關故障的發生，建議根據產品的技術條件，研究制定相應的篩選技術要求，并有針對性地進行以下故障預防可靠性檢查。例如：

In order to ensure the quality and reliability of the terminal and prevent the occurrence of relevant faults, it is recommended to study and formulate corresponding screening technical requirements according to the technical conditions of the product, and carry out the following fault prevention reliability inspection. For example:

在電氣設備中，經常會發現個別芯線壓接線未交付到位，或交付后無法鎖定，接觸不可靠。分析原因是個別安裝孔的螺牙有毛刺或污垢。尤其是在使用出廠時已安裝在插頭插座上的后幾個安裝孔時，發現缺陷后，必須將其他已安裝的孔中的壓接線一一卸下，更換插座。

In electrical equipment, it is often found that individual core crimping wires are not delivered in place, or cannot be locked after delivery, and the contact is unreliable. The reason is that the screw teeth of individual mounting holes have burrs or dirt. Especially when using the last few mounting holes installed on the plug and socket when leaving the factory, if defects are found, the crimping wires in other installed holes must be removed one by one and the socket must be replaced.

此外，由于線徑和壓接孔徑選擇不當，或壓接過程操作不正確，也會造成壓接端不牢固的事故。為此，在成品出廠前，制造商應對交付的插頭（座）樣品的所有安裝孔進行徹底的測試，即使用裝卸工具模擬帶有插針的電線或千斤頂?shù)轿?，檢查是否能鎖定。根據產品的技術要求檢查每根壓接線的拉拔力。

In addition, due to the improper selection of wire diameter and crimping aperture, or the incorrect operation of crimping process, it will also cause the accident that the crimping end is not firm. Therefore, before the finished products leave the factory, the manufacturer shall thoroughly test all the mounting holes of the delivered plug (seat) samples, that is, use the loading and unloading tool to simulate the wire with pin or Jack in place and check whether it can be locked. Check the drawing force of each crimping wire according to the technical requirements of the product.

菲尼克斯端子廠家提醒大家，如果沒有可靠的接線端子，就沒有可靠的系統工程。預防和分析是每個企業必不可少的過程。通過接線端子的可靠性篩選，發現各種故障模式和故障機制。可以分析大量經驗教訓，消除各種隱患，為改進設計、工藝、檢驗和使用提供科學研究。

Phoenix contact terminal manufacturer reminds you that if there is no reliable terminal, there is no reliable system engineering. Prevention and analysis are essential processes for every enterprise. Through the reliability screening of terminal blocks, various fault modes and fault mechanisms are found. It can analyze a large number of experiences and lessons, eliminate various hidden dangers, and provide scientific research for improving design, process, inspection and use.

依據是修改和制定碼頭技術條件的重要依據，為防止不必要的損失提供技術保障。更多有關端子的相關信息就來網站www.haoyuanxb.com咨詢吧！

The basis is an important basis for modifying and formulating the technical conditions of the wharf, and provides technical support for preventing unnecessary losses. For more information about terminals, please visit www.haoyuanxb.com Com consultation!